1. All 3M Products
  • 3M™ Red Dot™ Neonatal Pre-Wired Limb Band Monitoring Electrode, 2284, 0.9 in x 0.7 in (2.2 cm x 1.7 cm), 18 in (45.72 cm) radiolucent leadwire, 3 per bag
  • 3M™ Red Dot™ Neonatal Pre-Wired Limb Band Monitoring Electrode, 2284, 0.9 in x 0.7 in (2.2 cm x 1.7 cm), 18 in (45.72 cm) radiolucent leadwire, 3 per bag

    3M ID 7000128623
    • Made with a gentle adhesive that helps reduce the risk of skin trauma
    • Radiolucent
    • Smaller size for neonates
     More...
    Specifications
    Brand
    Red Dot™
    Case Packaging
    3 Electrodes/Package; 100 Packages or 300 Electrodes/Case
    Department
    NICU
    Electrode Size
    0.9" x 0.7"
    Electrode Type
    Infant Pre-wired, Monitoring, Neonatal Pre-wired, Pre-wired
    Gel Type
    Conductive Adhesive
    Material
    Soft Cloth
    Model
    2284
    Monitoring Event
    Pediatric Monitoring
    Package Contents
    3 Electrodes/Package
    Patient
    Neonatal, Pediatric
    Product Type
    Electrode
    Product Use
    Monitoring
    Radiolucency
    Radiolucent
    Skin Prep Included
    No
    Skin Type
    Fragile, Normal
    Details
    • Made with a gentle adhesive that helps reduce the risk of skin trauma
    • Radiolucent
    • Smaller size for neonates

    Specially designed for neonatal patients, 3M™ Red Dot™ Neonatal Monitoring Electrode are pre-wired for ease of application and trace quality.

    How to apply

    Application instructions

    Person cleaning the skin where the electrode will be placed

    Prepare the skin. Application sites must be clean, dry, and free of any body lotions. Cleaning with isopropyl alcohol should be avoided or limited to situations in which electrode adhesion is an issue (exessively oily or lotion covered skin). If alchohol is used, allow it to dry prior to electrode application.

    Person making an X on the skin wtith the abrader

    Excessive hair at the site should be removed by clipping. Gently abrade the skin on the back of some electrode (blue strip or gray disc) or 3M™ Red Dot™ Trace Prep. Make an X on the skin with the abrader. Apply the electrode and then gently rub around the electrode to set the pressure sensitive adhesive.

    Person applying the electrode to the patients shoulder

    Apply the electrode. If using snap connection leadwires, connect the leadwires to the electrodes onto the patient. Avoid pressing on the stud when the electrode is on the patient. After placing the electrode on the patient, round your finger around the front label to activate the pressure sensitive adhesive.

    Removal instructions

    Person removing the electrode

    Remove. In order to remove, loosen one side of the electrode. Grasping the full width of the electrode, slowly and gently pull it back over itself.

    Electrodes should be removed in the direction of hair growth whenever possible. Keep the electrode close to the skin surface as you pull it back, and support the skin immediately adjacent to the adhesive being removed.

    Contact a representative

    All fields are required.

    • Enter your 10-digit phone number. Numbers only (5555555555).
    • Please confirm your information is correct.

    3M will use the information to respond to your request and in accordance with our Privacy Policy.



    3M takes your privacy seriously. 3M and its authorized third parties will use the information you provided in accordance with our Privacy Policy to send you communications, which may include promotions, product information and service offers.


    Loading wheel

    Thank you for contacting us! Logo
    Thank you!

    Your request has been submitted successfully. A representative will contact you shortly.

    Sorry Logo

    Sorry!

    We can’t seem to complete your request. Please try again.

    Other 3M Sites:
    Partner portal
    Follow Us
    The brands listed above are trademarks of 3M. Used under license in Canada.
    Change Location
    Canada - English | Français